Phones answered 24/7Manchester, NH
Call (833) 490-5225
(833) 490-5225
Manchester, Hillsborough County, and the towns around it

Water in your Manchester home? Shut the main, then call.

A pipe that froze in an attic or cellar wall, an ice dam that leaked into a ceiling, a Merrimack or Piscataquog rise, or a basement drain that pushed back during a downpour. Call (833) 490-5225 at any hour. A crew is dispatched as fast as one is available, and the emergency stage is explained before equipment starts.

  • Answered 24/7
  • Frozen pipes and ice dams
  • Merrimack flood cleanup

Get a fast quote

Fastest: call (833) 490-5225. Or send this and we call you back.

Today in Manchester

Local weather drives activity here: heat, humidity and rain change what shows up week to week.

    Call (833) 490-5225

    Manchester & Hillsborough County

    Local water damage restoration you can reach by phone

    Manchester Water Damage Restoration at a glance

    Manchester Water Damage Restoration answers water damage calls for Manchester, Hillsborough County and the towns around it, 24/7. A crew is dispatched as fast as one is available. Standing water comes out first, then the wet structure is dried to measured readings, and dated photos and logs are kept for the homeowner and the insurer.

    Calls in the Merrimack Valley tend to start in one of four places: a pipe that froze and split in a cold attic, cellar or crawl space; meltwater from an ice dam that found its way under shingles and into a ceiling; a river or brook that left its banks; or a basement drain that pushed water back during a heavy rain. The first steps differ by source, but the order never does: stop the water, take it out, then dry the structure until the readings say it is dry.

    While you wait for a crew, close the main valve if the water is coming from a pipe, keep the power off in wet rooms, stay out of standing water and photograph the damage from the dry side of the room. Those details are the first thing the crew asks about, and they shorten the first visit. If a ceiling is bulging with water, stay out from under it.

    Services

    Water damage services for Manchester homes and businesses

    Pick a service for symptoms, process and typical cost, or call and describe what you hear and see.

    Burst Frozen Pipe Water Damage

    Water from a split pipe is stopped at the source, extracted and dried out of walls, ceilings and floors until readings are normal.

    Ice Dam Water Damage

    Meltwater that backed up under shingles is traced into the ceiling and wall below, removed, and dried until the readings are dry.

    Merrimack River Flood Water

    River water that entered a home or building is removed, the contaminated materials taken out, and the structure dried and checked.

    Spring Snowmelt Flooding

    Meltwater and thaw rain that pooled against a foundation and came inside is pumped out and the structure is dried to readings.

    River Flood Cleanup After Major Rain

    After days of heavy rain push a river or stream into homes, the cleanup covers extraction, removal, cleaning and drying across several buildings.

    Basement Flooding After Heavy Rain

    Rain, thaw and a high water table push groundwater into Manchester cellars. Standing water comes out first, then the structure is dried.

    Sump Pump Failure Water Damage

    When the pit overflows because a pump stalls, loses power or cannot keep up, the cellar fills. Water out first, then drying and a cause check.

    Sewer Backup Cleanup

    Sewage in a cellar is contaminated water. Keep out, let a crew extract it, remove porous materials and sanitize before drying.

    Water Heater Leak Damage

    A leaking tank empties onto the cellar floor. Shut off the supply, then extract the water and dry the area around the heater.

    Washer and Appliance Leak Damage

    Washers, dishwashers and ice-maker lines soak floors, cabinets and the ceiling below. Shut the valve, then extract and dry.

    Ceiling and Drywall Water Damage

    A stained, sagging or bulging ceiling means water is trapped above it. The board is opened, the source found, and the cavity dried before it is closed.

    Hidden Water Leak Detection

    When a spot will not dry or a smell will not leave, the leak is behind a surface. Meters, a camera and a pressure check trace it to the source.

    Crawl Space and Basement Moisture

    Dampness in a cellar or crawl space is measured, dried and traced to where it comes from, so it stops feeding mold and rot.

    Mold After Water Damage

    Mold follows moisture. The fix is to dry the building, contain and remove growth on porous material, and clean what can be cleaned.

    Mill-Era Multi-Family Water Damage

    When one unit leaks, others get wet. Brick blocks and shared walls call for a plan that covers every unit, owner and floor involved.

    Why homeowners call us

    Why Manchester Water Damage Restoration

    Answered at any hour

    Phones are answered 24/7, holidays included, so a call at 3 a.m. about a split pipe in a February cold snap reaches a person who can walk you through the main valve and the breaker before anyone arrives.

    Built for old New England buildings

    Plaster over lath, brick party walls, stone cellars and balloon-frame cavities hold water differently from a newer drywall house. The drying plan is set from readings in the actual walls, not from a template.

    Water removed before drying begins

    Standing water is pumped or extracted first, because drying equipment cannot do that job. Then the floor, the wall bases and the cavities are read so the crew knows what is wet and what only looks wet.

    Dry by the reading

    Air movers and dehumidifiers stay until the meter shows framing, plaster, drywall and subfloor at their dry targets, not for a fixed number of days. The readings are shown to you at each visit.

    Records for your insurer

    Dated photos, moisture readings and a list of what was removed are kept for the file, so the homeowner and the insurance company are looking at the same facts.

    Straight about limits

    The crew removes water and dries the structure. A split pipe goes to a plumber, a leaking roof to a roofer, and whether a loss is covered is decided by your insurer. You hear that at the start.

    How it works

    From phone call to fixed, in four steps

    1. Close the valve, then call

      If a pipe, heater or appliance is the source, shut off the main and stay clear of wet outlets and cords. Then call the number at the top of the page. The first questions are where the water is coming from, whether it is still coming and which floors are wet.

    2. Water comes out first

      The crew confirms it is safe to enter, then pumps or extracts standing water from the lowest point. Wet pad, soaked insulation and anything contaminated are identified and described before they are removed.

    3. Read it, then dry it

      Moisture meters show where water has traveled into plaster, framing and floors. Air movers and dehumidifiers go where the readings say, and they run until the structure reaches its targets.

    4. Record and hand over

      Photos, readings and a removal list go to you for the insurer. Repairs such as new drywall, flooring or a plumbing fix are quoted separately once the structure reads dry.

    What should you do first when pipes freeze and split in a Manchester house?

    Shut off the main water valve, open a faucet to relieve pressure, switch off power to any wet area and photograph the damage. Do not use a flame to thaw a pipe. Then call, because a split pipe can keep leaking inside a wall long after it looks like a small drip.

    Pipes in uninsulated attics, basements, crawl spaces and exterior walls are the usual victims of a New Hampshire cold snap. The split often does not show while the pipe is frozen. The water arrives when it thaws, which is why a ceiling stain or a wet floor can appear hours after the coldest part of the night.

    Find the main before you need it, and learn which way it turns. In many older Manchester houses it sits in a cellar corner near the front wall, sometimes behind stored boxes. If you cannot find it, say so on the call and the crew will talk you through the search. The frozen pipe guide lays out the steps in order.

    How does an ice dam put water inside the house?

    Snow melts on a warm roof, runs to the cold eave and refreezes into a ridge. Meltwater backs up behind that ridge, works under the shingles and drips into the attic, the ceiling and the wall below. The leak shows up inside long before it shows on the roof.

    Ice dams leak slowly and spread sideways. Wet insulation, a stained ceiling in the room under the eave and water running down inside an outside wall are the common signs. Raking snow or chipping ice off the roof can damage shingles and is risky on a ladder, so leave that to a roofer.

    The crew's part is the inside: removing wet insulation where it holds water, reading the ceiling and wall, and drying them. The ice dam guide covers what to photograph before anything is cut open.

    Why does heavy rain sometimes bring sewage up a Manchester basement drain?

    About 70 percent of Manchester's sewer system is combined, carrying storm runoff and household waste in the same pipes. In heavy rain those pipes can fill faster than they drain, and the pressure can push water back toward the lowest drain in a house. Sewage is treated as contaminated.

    That share comes from the EPA's settlement with the city, which also records that combined sewer overflows discharge to the Merrimack and Piscataquog Rivers and to Ray Brook and Tannery Brook. It is a fact about the system, not a statement that any particular street or house will flood. A basement drain that backs up in a storm is still worth treating as a real possibility.

    A sump pump that cannot keep up, a window well that fills and seepage through a stone foundation can look like a sewer problem at first. The crew tells them apart by where the water enters and what it looks and smells like. The sewer backup guide explains how those jobs differ.

    What do the Merrimack and the Piscataquog do to the neighborhoods beside them?

    Both rivers have flooded Manchester and the towns around it. The Merrimack rose about 20 feet at Hooksett in March 1936, and in May 2006 it ran about 10 feet over flood stage in Manchester while dozens of homes flooded. River water carries silt and is handled as contaminated.

    In 1936 the Amoskeag dam in Manchester held after more than 500,000 sandbags were used. In May 2006 heavy rain starting May 11 sent the Suncook River into a new channel in Epsom and left Goffstown reporting 82 damaged structures on the Piscataquog. Dollar totals for that storm differ between sources, so none are printed here.

    None of that means the water will come back to a given address, and this site does not say which blocks are at risk. It does mean flood water in a New Hampshire cellar is a local, documented thing. The Merrimack flood guide covers the first steps.

    Service areas

    Serving Manchester and all of Hillsborough County

    Derry

    ZIP 03038, 03041

    Bow

    ZIP 03304

    Weare

    ZIP 03281

    Service area map: Manchester ZIP 03101 (Downtown and Millyard), Manchester ZIP 03104 (North End), Manchester ZIP 03103 (South Manchester), Manchester ZIP 03102 (West Side), Manchester ZIP 03109 (East Side), Bedford, Hooksett, Auburn, Goffstown, Candia, Merrimack, Londonderry, Litchfield, Derry, Chester, Bow, Dunbarton, New Boston, Pembroke (Suncook), Amherst, Mont Vernon, Raymond, Weare, Sandown, Deerfield, Nashua, WindhamManchester ZIP 03101 (Downtown and Millyard)Manchester ZIP 03104 (North End)Manchester ZIP 03103 (South Manchester)Manchester ZIP 03102 (West Side)Manchester ZIP 03109 (East Side)BedfordHooksettAuburnGoffstownCandiaMerrimackLondonderryLitchfieldDerryChesterBowDunbartonNew BostonPembroke (Suncook)AmherstMont VernonRaymondWeareSandownDeerfieldNashuaWindhamManchester (base)N

    Manchester, NH · 25 km service radiusCall (833) 490-5225

    Not on the list?

    We also cover many smaller communities across Hillsborough County. Check your ZIP.

    Job stories

    Typical jobs around Hillsborough County

    Typical job
    Illustration: Typical: a split pipe in a cold attic after a hard freeze

    Typical: a split pipe in a cold attic after a hard freeze

    What homeowners notice
    After a cold snap, a stain has spread across a bedroom ceiling and water is dripping from a light fixture. A supply pipe in an uninsulated attic space froze, split and began leaking as it thawed.
    What we do
    The crew confirms the power to the room is off, catches and extracts the water, removes wet insulation above the ceiling and reads the ceiling and wall below. Air movers and a dehumidifier run until the readings reach target. A plumber repairs the pipe separately.
    What to expect
    The homeowner receives dated photos, readings and a list of what was removed, and the repair of the ceiling finish is quoted once the framing reads dry.

    one extraction visit, then drying visits typical visit

    Typical job
    Illustration: Typical: an ice dam leak down an outside wall

    Typical: an ice dam leak down an outside wall

    What homeowners notice
    After weeks of snow and a thaw, meltwater has backed up at the eave of an older house. A brown stain has appeared on the ceiling beneath the roof edge and water is running down the inside of an exterior wall.
    What we do
    The crew photographs the stains, removes saturated insulation where it holds water and reads the ceiling and wall cavity. Drying equipment is set to pull moisture from the cavity, and the roof side is left to a roofer.
    What to expect
    The record shows the readings and the wet extent, so the insurer and the roofer are working from the same facts.

    several visits over the drying period typical visit

    Typical job
    Illustration: Typical: river water in a cellar after days of heavy rain

    Typical: river water in a cellar after days of heavy rain

    What homeowners notice
    After days of rain, a river near an older house has risen and brown water has come into the cellar, leaving silt on the floor and a line on the stone walls. The furnace sits low in the room.
    What we do
    The crew confirms the power is off, pumps the standing water from the lowest point, and removes silt-soaked stored items and any porous finish. The floor and wall bases are cleaned as contaminated, then dried with dehumidifiers until the readings reach target.
    What to expect
    The homeowner has photos, readings and a removal list, and the furnace is left for a licensed heating trade to inspect.

    several visits over the drying period typical visit

    See more job stories

    Need water damage restoration today?

    Call any hour and explain what is going on. You get a clear price before any work starts.

    Guides

    Answers before you call

    FAQ

    Frequently asked questions

    Will a crew come out at night or on a holiday?

    Phones are answered 24/7, holidays included. A crew is dispatched as fast as one is available, and no arrival time is promised. On the call you are told what to do while you wait, starting with the main shutoff and the power.

    Do you handle mill buildings and multi-family blocks?

    Yes. Brick tenement blocks and converted mill buildings are common in the city's older districts, and one unit's leak often reaches the next. The mill-era multi-family page explains how those jobs are run.

    Is the water in my cellar safe to touch?

    Not until the power to the area is confirmed off, and not if it came from a drain, a river or a brook. That water can carry bacteria and is handled as contaminated. Stay out and wait for the crew if you cannot tell the source.

    Can you thaw and repair a frozen pipe?

    No. The crew removes water and dries the structure. A plumber repairs or replaces the pipe, and the drying record helps the plumber see where the water went. The burst pipe page explains the split of work.

    How is the price decided?

    By a walkthrough, not a phone guess. The area wet, the materials that must come out and the readings set the scope, and the emergency stage is explained before equipment starts. The pricing page lists what moves a quote.

    Will drying stop mold?

    Fast, complete drying is the best prevention, because mold needs moisture. Materials that stay wet can still grow it, so hidden cavities are checked. The mold page covers what happens if it has already started.

    WhatsApp